Motorcycle carburettor gaskets

Richard

Reliable opinion

Ebonite carburettor washer with GY6 4T O-ring has not been installed, as the pipe is the wrong size

JanD

Reliable opinion

Moped - Barton Fighter Eco 2020 The store's merchandise filter specified as if this pad would fit my machine. It does not fit!!! The main hole is 3.5 mm too small, and worse, the spacing of the screws is also strongly too small. I had an emergency situation and sanded the holes to my needs provisionally. But I am disappointed. For 139FMB engines, GMoto does ... more

Hubert

Reliable opinion

I ask users when installing this gasket to clean the surface of the carburetor, diaphragm and seat at the engine. This should be done at least with extraction gasoline from the surface dirt, because in my case I had to clean it twice because in this place it unnecessarily drew left air and did not turn on the revs, after cleaning it laughs like a factory one

Bartosz

Reliable opinion

A 110ccm quad by bemigermany with a TZH152FMH engine (top starter) nothing particularly different from other Chinese 110 engines. The gasket fits well to the intake with a diameter of 20mm (to the intake of 19mm will also fit) and carburetor. It does not let left air through, I recommend it

DAWID

Reliable opinion

PEOPLE THERE IS NOTHING TO WAIT FOR WHEN IT LEAKS YOU HAVE TO REPLACE THE SET OF GASKETS IT'S EASY 15 MINUTES AND YOU'RE DONE, THE COST IS SMALL BUT THE QUALITY IS MEGA PERFORMANCE CHEAP, EASY FAST AND AESTHETICALLY PLEASING ON THE GASSER AND NOT ALWAYS BEEHIVE E TAM . NOW I WILL ALWAYS BUY SUCH A SET OF GASKETS DURING THE NEXT OVERHAUL I HEARTILY RECOMMEND ... more

Piotr

Reliable opinion

The supplier showed professionalism regarding the preparation AND delivery of the shipment of parts for Junak M10. I was very impressed by the electronic notification system of the status of the order until delivery to the addressee. Very fast delivery and without courier.

Krzysztof

Reliable opinion

What to write here a lot. I have a moped Romet C1 and it is always difficult to fit some parts to it. In the case of the handle, which I also ordered from this website, I succeeded, but not with the gasket. I do not see the point of sending it back, because it would be a terrible waste of bilge(

Marek

Reliable opinion

Super gasket, thanks to it you no longer need to cut replacement gaskets of different quality materials. For the few zlotys you can have the perfect gasket, so you can professionally install the carburetor and get rid of leaks from the intake manifold.

Dawid

Reliable opinion

The gasket for the float chamber quality is good and has the original dimensions. Unfortunately, the 3 fiber gaskets (red) do not seal well, they are too thin and let the fuel through. The gasket for the float chamber cap is too large.

Robert

Reliable opinion

The gaskets are well made and fit the manifold.I replaced them because I installed a new gasser.It is advisable to replace the gaskets when replacing the manifold or gasser,to better fit the new components.

Adam

Reliable opinion

I put it on my SHL M11. The build quality is very good. After assembling the carburetor and driving a dozen kilometers, I only tightened the float chamber a little because there was some fuel soggy around the chamber.

Adam

Reliable opinion

I have no reservations. Product of very good quality. It fits perfectly. I have been a faithful buyer from this seller for years, large selection, high quality,no complaints. Knowledgeable sales staff at a high level.

Bartosz

Reliable opinion

The gasket fits well, made of solid material, it is important to tighten the carburetor with feeling, then the gasket will do its job and will not deform. I recommend a light wetting with commodity.

Ostrowski

Reliable opinion

My machine is a 4t baotian 50cm scooter after tiuning now 72cm bigger nozzle bigger spigot necessary bigger spigot washer this product meets all the requirements I highly recommend it

Marek

Reliable opinion

Cut to size gasket does not differ from the original in any way, in addition to the fact that it is brand new and super-fitted, as well as the material from which it is cut is not just anything but a decent . I recommend

Łukasz

Reliable opinion

Nice service, everything as described, super packed and protected, fast shipping. Gasket for the carburetor made of good material, well fitted to the carburetor. I recommend this store.

Petr

Reliable opinion

Hello the gasket fits well I used it on Jawa Betka 50 so the new pioneer, but be careful not to crack it is the same gasket that was there originally meets 100%

Grzegorz

Reliable opinion

junak m10 very good quality, very well fitted .

Piotr

Reliable opinion

Nice thick gasket ( although the old ones were even thicker and this one could be like that too) Overall I recommend. It is certainly better than what is added to the whole set of gaskets.

Adam

Reliable opinion

The pad is nicely made, it's a pity that it's made of poor materials, but for a few zlotys you can't expect miracles, but it's worth adding a few zlotys and buying a better one, best regards