Forgot password
Order status
Free delivery from euro
Motorcycle engine seal sets - Page 3
Options +4 
Browse Motorcycle engine seal sets - Page 3 by manufacturer
Products reviews
WSK from 1969 B1, the so-called two-frame. Gaskets fitted, fit all the holes, when taking the engine apart again, which happened to me ;) because orphan to do it again calmly all the gaskets kept whole so made well enough. during operation, operation so far does not leak, they hold well. I recommend
Review translated automatically
Reliable opinion
The delux gasket is missing a lot, the holes do not fit perfectly for sure. i used maybe 3 from the kit so i do not know how the others fit. Float chamber gasket failed to fit because it did not fit at all. I was guided by the reviews but I see that these super reviews are probably for looks or for that 400zł voucher. P
Review translated automatically
Reliable opinion
wsk 175 wind engine, the seal is made of something that resembles plastic, in the rear part where the gearbox fits, in the front where the crankshaft is shifted by a few centimeters there is no possibility to put it on, it is only suitable for wringing out
Review translated automatically
Reliable opinion
Romet Kadet 780 1988. Once again, the gaskets fit very well. We have a set for virtually the entire engine and accessories.
Review translated automatically
Reliable opinion
Gaskets super, probably the best there are. Fits elegantly motorcycle does not leak and can stand at home.
Review translated automatically
Reliable opinion
GOOD QUALITY . HANDY ITEM . VISUALLY ALSO OK . MATERIAL FROM WHICH IT WAS MADE SEEMS OK .
Review translated automatically
Reliable opinion
S38 engine - this gasket set is the optimal choice for this engine. Everything fits as it should.
Review translated automatically
Reliable opinion
I purchased the kit because I needed a clutch-side lid gasket. The gasket turned out to be completely mismatched, even tragic, so much so that I used the old one. Gmoto should change the product because from what I gather this is not the first negative review of these gaskets. In another well-known wholesaler you can buy perfectly matched which means that you can make good gaskets. As for quality and aesthetics, I will not comment because the mere fit made it impossible to use the gasket
Review translated automatically
Reliable opinion
WFM-125 M06 motorcycle from 1961. Carcass gasket a little too big. Gasket made of paper .Quality average. But it is possible to fit. Clutch cover gasket fits perfectly. Quality good. Cylinder gasket is too big at the flushing channels, does not fit WFM. Quality good. The head gasket does not fit the WFM. The holes are too large. The diameter of the hole for the piston is too large. Quality good. I bought these two from a competitor and they fit well. Massacre. Just to sell.
Review translated automatically
Reliable opinion
Romet Kadet, engine 023, a set of gaskets that is most worthwhile, a copper head gasket, a thick and solid carburetor/cylinder gasket and many other useful for this engine, it is not worth buying by the piece. Just remember that for these gaskets do not use any red silicones, etc. It is enough that we lubricate with lubricant and tighten evenly, and nothing will leak .
Review translated automatically
Reliable opinion
Gaskets rather good quality but you pissed me off because I specifically took the deluxe so that they would be decent, and here it turns out that the box is missing one gasket in front of the carburetor, and there should be two, I did not expect that I will have to make up a gasket even though I bought the most expensive ones that were in the store, next time check the completeness of your products, greetings
Review translated automatically
Reliable opinion
I see that they are no longer available and I hope that you are changing the manufacturer. Towards the end (as I was assembling the last two engines) the clutch cover gasket was already dimensionally out of all standards (too big). The gasket for the crankcases was also barely making it through the holes. I personally am done with this product. I had some pics, but I can't add to the feedback, maybe browser fault.
Review translated automatically
Reliable opinion
WSK 125, 1982. Gaskets work well as an optional extra. If it is not possible to make scans of the lid and carcass and print a dedicated gasket, you can trust them. In the case of the lid, a little "intervention" with scissors came in handy and gluing went without problems. A big plus is the material - crystallite. I recommend.
Review translated automatically
Reliable opinion
I have a 1998 Derbi Senda R 50, a motorcycle that is quite rare these days. The gaskets I ordered do their job well, they are solidly made and thanks to them I do not have to worry about the tightness of my engine. The price is affordable and really worth it compared to the quality of the product. I heartily recommend!
Review translated automatically
Reliable opinion
Aprilia rs50 98r- the quality of the gaskets is very poor, they do not fit (those from the cylinder) on the head, they are made of the cheapest rubber. I would advise you to withdraw this set from sale, because only the gasket under the clutch cover and between the cylinder and the carter fit, and the rest is suitable for trash :)
Review translated automatically
Reliable opinion
A very rich set of gaskets. Nevertheless, I have doubts about the thickness of the gaskets themselves and whether they will perform their role well enough. Some also stick out quite a bit from the engine giving a not quite expected result. Nevertheless, I recommend it as much as possible.
Review translated automatically
Reliable opinion
The workmanship of the gaskets leaves much to be desired, although the material seems solid. Gaskets for the carburetor do not fit, they have to be reworked, cut, the holes are applied too wide. After contact with gasoline, the gasket tends to ripple. Overall, I do not recommend.
Review translated automatically
Reliable opinion
Romet ogar 205, 50 cm³, 1987. The seals are made of a nice material, they are thick, well lapped and adhere well. The problem with leakage from under the clutch Deck is gone. One minus I received a gently bent muffler gasket, but other than that, I recommend heartily
Review translated automatically
Reliable opinion
Mosquito Mosquito s38 1975-purchased parts are of high quality in terms of workmanship, aesthetics, efficiency of operation -I recommend many motorcycles I assemble and with this company super to cooperate-mega efficient shipping 24 hours to the other end of the Polish b.good contact with the seller.RECOMMENDED
Review translated automatically
Reliable opinion
Simson S51, everything purchased G-moto each part is very good quality parts are well finished, installation without any problems I recommend in good conscience I have been buying for a long time and yet G- Moto has not let me down the same with the delivery always on time
Review translated automatically
Reliable opinion
The paper ones not very decent though would have sufficed,but unfortunately they were glued to the film so that I destroyed most of them trying to peel them off [I did it very gently].The only thing that came in handy for me was the head gasket,exhaust and orings.
Review translated automatically
Reliable opinion
Suzuki TS 50 XK 1991 after changing the engine to minarelli am6 because the parts are more available. The build quality of these gaskets is good, but I don't like the packaging. I had to struggle a bit to get them out. That's the only downside.
Review translated automatically
Reliable opinion
I tested the gaskets so far only from the carburetor. The gaskets are thin and do not fit. The gasket from the chamber where the float is located is too big. The other one mounted at the head has decorated screw holes badly. My engine is a Deazamet 023.
Review translated automatically
Reliable opinion
Gaskets are definitely better than paper gaskets, the engine does not leak even without the use of silicone, and above all - without consequences you can remove several times, for example, the clutch cover for adjustment - and the gasket will still hold.
Review translated automatically
Reliable opinion
Hello, I own two 1985 M-2 motorcycles and one 1987 M-3. I am currently in the process of rebuilding each in turn. The parts I bought from Gmoto met my expectations. They were of good quality and fit without any problems.
Review translated automatically
Reliable opinion
WFM M06, S01 engine - the best set of gaskets I have bought. Very good fit. No need to cut anything , especially the gasket under the cylinder. Fits very well and does not obscure the channels. I recommend it as much as possible.
Review translated automatically
Reliable opinion
WSK 125 1985.Gaskets made very carefully and importantly with the right material. Shape perfect , holes in the right places, all without any corrections perfectly adhere as needed. I recommend.
Review translated automatically
Reliable opinion
Head gaskets aluminum, which is what they are supposed to be. The carburetor throat gasket as well as the cylinder gasket not quite measured right. But overall it was possible to assemble the engine correctly on this set
Review translated automatically
Reliable opinion
Engine gasket kit - crngelite CZ 350. Perfect working kit for my CZ 350.Always find the right things I need I am happy to buy from you.Fast and honest.
Review translated automatically
Reliable opinion
Engine gasket kit - crngelite CZ 350. Perfect working kit for my CZ 350.Always find the right things I need I am happy to buy from you.Fast and honest.
Review translated automatically
Reliable opinion
So far, one of the gaskets, namely the timing pkrywa gasket mismatched ( too wide in relation to the holes ) in my case I had to enlarge the holes in the gasket to be able to install it.
Review translated automatically
Reliable opinion
Shipping fast and no problems , package nicely packed with no damage . Parts as described on the website 100% . All new packaged - safety first class ! And of course the cheapest !
Review translated automatically
Reliable opinion
I have an april rs 50 from 2002 I have replaced several things in it. The gaskets I bought are of very good quality and easy to install. I rate the product as very good.
Review translated automatically
Reliable opinion
Very good fitting gaskets for AM6 engine at affordable price never had any problem with them. HIGHLY RECOMMENDABLE. P.S nice packaging of gaskets
Review translated automatically
Reliable opinion
Another wonderful and glorious gasket kit for minarelli am6 that doesn't fail at all and doesn't let any oil through, not a single drop of oil!
Review translated automatically
Reliable opinion
kinroad chopper fit perfectly and nothing leaks.gaskets of good workmanship and I recommend buying at gmoto because there are cheap parts and generally everything goes to get.
Review translated automatically
Reliable opinion
I own a 2003 Derbi Sende that is still on the EBS engine I ordered these gaskets for the second time and the engine sealed nothing leaks. I recommend for this price.
Review translated automatically
Reliable opinion
Motorhispania 50cm well made product at a decent price that fits the Am6 perfectly and includes everything needed to mount the motor
Review translated automatically
Reliable opinion
The gaskets that fit the engine gait needed a slight trim in some places still fit like a glove to the 154fmi engine
Review translated automatically
Reliable opinion
k750 the transaction went smoothly the product description was consistent the shipment arrived on time recommend to other users
Review translated automatically
Reliable opinion