Motorcycle parts
Honda ST 1100 Pan European - Page 4

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-12, 15:59

View original

Krzysztof

Honda Africa Twin XRV 750 1999. The piston fits the calipers on older models, the pistons for my motorcycle are 3mm shorter. I ordered the set with the idea of shortening it. The material turned out to be soft compared to the original(this does not prove its strength, therefore the rating of 3 from the quality), cutting 3mm on the lathe did not overheat the pad and after protecting it on the turning side with an appropriate specific will ensure that it will not lose its anti-corrosion properties. A perfect replacement for the twice more expensive original. The width agrees, the quality of the seals seems to be OK, after installation it does its job - I recommend.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2022-01-08, 09:15

View original

Dariusz

The mounting rubber of the exhaust manifold bracket, and the end muffler, fits tightly and stabilizes them very well, by the way, rumor has it that the TOURMAX brand manufactures OEM parts for HONDA motorcycles, and this can be seen, with disassembled worn parts (markings from casting molds).

Review translated automatically

Reliable opinion

2020-06-22, 11:48

View original

Stanisław

I recommend the clutch pump repair kit from Tourmax. Replacement is trivially easy, and all the necessary things that wear out in such a pump are included in the set. For a small amount of money, you can easily recondition a malfunctioning pump and eliminate clutch problems.

Review translated automatically

Reliable opinion

2018-05-30, 16:49

View original

Krzysiek

I have a replica honda magna 2003 year 125ccm I was looking for rectifiers on the internet for a long time and finally found them here fast shipping I fired it up the first time good quality product solid I recommend it

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2021-02-02, 22:02

View original

Daniel

99r Honda VFR 800 FI RC46. Simple quick installation. Filter adapted for an ordinary ring wrench. Uses k&n products great look and performance. I recommend

Review translated automatically

Reliable opinion

2020-06-22, 13:07

View original

Stanisław

The whole kit fits perfectly. I recommend to regenerate the baked clutch. Previously it was impossible to move it, now it goes in with fingers without any problems.

Review translated automatically

Reliable opinion

2019-03-10, 10:47

View original

Mirosław

Kawasaki Z900. The filter is better made than the original. Very good ease of installation,I am 100% satisfied and recommend to everyone.

Review translated automatically

Reliable opinion

2019-03-15, 08:51

View original

Dominik

Honda varadero 125 XL. Replacement quick and easy. Candles of very good quality. The transaction went well. I recommend

Review translated automatically

Reliable opinion

2021-10-08, 12:10

View original

Artur

There is nothing to say about Hiflo and the quality of their products, so I usually choose their filters.

Review translated automatically

Reliable opinion

2021-06-29, 10:25

View original

Leszek

Honda XL 600 V Transalp. A filter like a filter, it's hard to judge it by eye. It screwed in easily and pleasantly. All indications are that it filters as God has commanded. Shouldn't there be an o-ring in the place where it is screwed onto the spigot protruding from the block? I can't hide the fact that I would be happy to win four hundred bucks because I need a clutch and cash is tight.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2019-05-17, 14:01

View original

Przemysław

Honda ST 1300 2002 rubbers fit very good material, they look nice, not everyone remembers that due to worn out rubbers the grip of shoes to the footrests is low which makes it easy to have an accident, safety first and foremost and if by the way the machine gains in appearance it is even better ;)

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2017-05-15, 22:44

View original

Maciej

Patient Honda CB600F Hornet, vintage 2001, non-functioning fan switch. What can I say, a top-notch product. After replacement, the fan spins and works at its best. This radiator fan switch is a great product, I would recommend it to anyone

Review translated automatically

Reliable opinion

2019-04-14, 18:38

View original

Mariusz

KIT purchased and installed on a 1996 Honda VFR 750.Everything fit, it worked, I am satisfied. I will mention that I met with very friendly service. And I guess this is the main reason that I will be shopping there. No photo because the parts are already installed.

Review translated automatically

Reliable opinion

2016-03-18, 21:30

View original

Rafał

Honda Shadow VT 750 Black Spirit RC48 2003. The filter compared to the previous one I had installed has a nut, which makes it much easier to install /remove the filter, in the absence of a special key for installation. Definitely a plus.

Review translated automatically

Reliable opinion

2016-04-21, 20:49

View original

Julita

Honda Deauville, year 2008, poj.700.Workmanship solid, well-fitted, no problems with installation, meet expectations. We will see how long they will serve :-).It was worth buying, but a piece of rubber should not cost so much ;-).

Review translated automatically

Reliable opinion

2021-03-31, 10:03

View original

Dominik

The seals look decently made. We'll see how with their durability. I'll admit that there were problems with installation and it took some time, but they are finally sitting in place. Now only field tests.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2023-05-29, 13:07

View original

Mariusz

When it comes to oil filtration in our motorcycles, K&N is simply in a class of its own. I've been using them forever and although it's just a filter I can't imagine another one in my machine. I recommend.

Review translated automatically

Reliable opinion

2021-06-03, 15:15

View original

Sławomir

I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.

Review translated automatically

Reliable opinion

2021-01-24, 16:53

View original

Bogdan

I own a motorcycle honda CBR 1000F, vintage 1966, capacity 1000 cm. This is another filter from this manufacturer that I bought, and I have never had any problems with them have always served their purpose.

Review translated automatically

Reliable opinion

2022-01-11, 15:35

View original

Wojciech

XL 600VA 1987 Oil easy to use does not require instructions. I recommend this product. Very good quality product for its price. Quick delivery hassle-free service. I recommend

Review translated automatically

Reliable opinion

2019-12-27, 13:32

View original

Mariusz

Honda Shadow VT 600 1994. The kit includes all the gaskets that need to be replaced when reconditioning the brake caliper, plus grease for the piston. Everything fit as in the original.

Review translated automatically

Reliable opinion

2020-03-30, 20:44

View original

Michał

The protections, compared to the old ones, are slightly wider, more rigid and more "expandable", which makes them fit perfectly into the groove in the lade blocking the sealers.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2021-03-20, 11:29

View original

Bartosz

The motorcycle is a Honda Transalp XL 600 The piston holds the dimension perfectly in every plane. The only difference is the different shape of the bottom of the piston, but this does not seem to affect the operation.

Review translated automatically

Reliable opinion

2019-01-14, 11:45

View original

Łukasz

Hello, The filter I purchased meets my expectations. Easier to install than standard filters. I am very satisfied and recommend, Greetings

Review translated automatically

Reliable opinion

2018-03-05, 18:27

View original

MARCIN

Hello, I bought this filter for oil change in my motorcycle i.e. 2006 Yamaha Stratoliner 1900. I have been using this product for about 5 years and am satisfied with it.

Review translated automatically

Reliable opinion

2024-09-24, 06:41

View original

Tomasz

The filter performs its function perfectly, after pouring off the old oil you can not see any flecks, etc. Thanks to the flexible gasket, I tighten it by hand and nothing leaks.

Review translated automatically

Reliable opinion

2019-04-27, 15:09

View original

Tomasz

Honda Vfr 750 rc 24 from 1987. The fit of the parts is very good making it a pleasure to assemble the exhaust system. It met my expectations as much as possible.

Review translated automatically

Reliable opinion

2021-12-12, 20:14

View original

Kordian

I always buy filters from HIflo and this time, too, everything fits until nice. I recommend to trust this brand as much as possible. Gmoto as usual at a high level. XJ600

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2017-06-18, 21:11

View original

Konrad

As great a plus as possible. The product in full working order, I recommend it as much as possible. I looked in many stores and here I found the cheapest. Price/quality 10/10.

Review translated automatically

Reliable opinion