Motorcycle parts
Honda CBF 500 - Page 6

2018-11-01, 20:15

View original

Krzysztof

I ordered the air vents with the motorcycle Honda XRV 750 Africa Twin - 1999 in mind. They fit the front calipers as well as the rear caliper. After screwing in, there is a little bit of thread sticking out(this is for a small minus), which is covered by a blanking rubber. They successfully replace the original, which is twice as expensive in the service. To the aesthetics and solidity rather can not be complained about - no burrs, the layer of zinc is placed on well-prepared steel. When tightening, care should be taken to select a perfectly matching wrench, scratches and destruction of the zinc layer can result in the appearance of rust in a fairly short time due to the fact that the material is steel. The downgrade for the material is due to the fact that I would prefer stainless steel instead of steel and zinc.

Review translated automatically

Reliable opinion

2018-11-01, 20:28

View original

Krzysztof

Honda Africa XRV 750 - 1999. I bought 12 pieces. This mounting rubber is found in several places on the motorcycle(the mount of the skull rack, oil cooler, plastic handles, etc.). It looks like the original, the rubber is flexible, you can bend it with two fingers with a stronger squeeze and it looks solid. Only the course of time can verify whether it is as solid. Dimensions: Hole diameter(nominal): 10mm Width of the entire rubber: 22mm Groove depth: 8mm

Review translated automatically

Reliable opinion

2017-07-15, 09:23

View original

Dawid

2000 Honda CBR 600F. The regulator works as expected + good price. I had previously tested a custom-made regulator, purchased at reg_mot.republika.pl, and unfortunately found that it drew current at a standstill, and was quite a bit larger than the standard regulator and required rearranging the components under the fairing. Tour-max regulator is the same size as the original, works perfectly. I am satisfied, I recommend it!

Review translated automatically

Reliable opinion

2019-01-12, 09:03

View original

Andrzej

Honda Cbf 500 2007. Sealers very good quality . Hassle-free installation. You can see at a glance that it is an original product of Athena.Oil burning I have already.I recommend.

Review translated automatically

Reliable opinion

2023-06-14, 02:35

View original

Mariusz

Installation: perfect fit to the frame holes (Honda CBR 600F4) Operation: charging at idle 13.4-13.7 V, maximum charging voltage 14.4-14.6 V (holds until cut-off, measured with a meter) The price is quite exorbitant, although the parameters reflect what it should be. Cheaper Chinese ones I'm afraid of, while here there is more confidence in the quality of the product.

Review translated automatically

Reliable opinion

2022-09-28, 18:40

View original

Stanisław

Honda NTV 650 Revere 97r. Kit well made, good quality parts, easy installation good fit. Replaces the original parts well, the pump works flawlessly. I would like to add that the kit was purchased on the recommendation of a Honda service employee because the original repair kit costs almost 4 times as much, and this one does its job 100%. I sincerely recommend.

Review translated automatically

Reliable opinion

2020-05-03, 00:23

View original

Maciej

Wsk 125 The frame is nice, you can't expect more from a plastic metallized one. It fits my wsk-i nicely. The only big minus is that it did not fit completely in the holes - I had to widen the holes with a drill both at the top and bottom. Other than that, installation was easy. I recommend the product for those who don't mind making up holes.

Review translated automatically

Reliable opinion

2020-03-30, 20:41

View original

Michał

Sealers without complaint. In a rigid and secure package a set of sealers and covers for two leaguers. Assembly trivially easy (for those who like and have an idea of DIY and small repairs). The fit is perfect. So far zero problem and the lags work perfectly in combination with Motul 10W oil.

Review translated automatically

Reliable opinion

2021-05-08, 07:38

View original

Andrzej

Plastic license plate frame looks like a good chrome material I changed the plate because I became the owner of a Suzuki Intruder VL 125 2000 year all in all. Looks super material fine that's why the price very low ugly comes longer.

Review translated automatically

Reliable opinion

2020-07-08, 19:23

View original

Waldemar

My machine is an 86 Honda Shadow VT 1100 . Purchased parts were not dedicated for this vintage , so as a novice user I bought blind and surprisingly they fit . Installation was no problem and the material and workmanship flawless . G Moto and product on pistket . LWG .

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r modelj recommend to everyone.

Review translated automatically

Reliable opinion

2017-07-11, 09:59

View original

Mariusz

I am a happy owner of a yamaha yzf 125r in which I recently noticed oil loss , I replaced the valve seals which I ordered from gmoto and I am very satisfied , solidly made . Easy to install and fit to my 2010r model I recommend to everyone.

Review translated automatically

Reliable opinion

2017-11-17, 07:02

View original

Jakub

We fitted the bearings to a 2004 Honda Hornet pc36. The installation went smoothly and the bearings seem indestructible ;) Well, but this is Mc International after all, the top shelf among parts for Japanese ;)

Review translated automatically

Reliable opinion

2019-06-17, 07:58

View original

Damian

In the category of quality/price very nice frame. Strong plastic imitating chrome. Aesthetics at a high level. Lightweight and durable And the license plate enters on contact ( for me a plus because there is no slack). I recommend

Review translated automatically

Reliable opinion

2021-06-03, 15:15

View original

Sławomir

I own a 2005 Honda CBF600. The sensor fit without a problem, plug and play. The replacement took 5 minutes. Fulfillment of the order was lightning fast, the product was with me the next day. Highly recommend.

Review translated automatically

Reliable opinion

2019-12-27, 13:32

View original

Mariusz

Honda Shadow VT 600 1994. The kit includes all the gaskets that need to be replaced when reconditioning the brake caliper, plus grease for the piston. Everything fit as in the original.

Review translated automatically

Reliable opinion

2023-09-11, 20:14

View original

sara

This mounting rubber is a great replacement for the rubbers found on the Honda CBR 600, but they are slightly smaller than the original (I personally didn't mind the installation)

Review translated automatically

Reliable opinion

2017-09-04, 10:25

View original

Mariusz

frame very nice, put on jawa ts 350 looks very good on this motorcycle, installation also very pleasant immediately changes the name of the motorcycle adds better charm

Review translated automatically

Reliable opinion

2024-09-25, 05:27

View original

Filip

Very good solution for those who want to replace the license plate frame with a new one. The price is very affordable. The quality of workmanship is also flawless. I can recommend

Review translated automatically

Reliable opinion

2024-05-17, 08:03

View original

Łukasz

Regulator worth the price, one of the best companies that makes reliable components for motorcycles. I am very satisfied. I will feel safe on the road

Review translated automatically

Reliable opinion

2020-05-13, 06:44

View original

Damian

Honda VTX 1300 2006. The master cylinder was reconditioned with the kit purchased. Fast, efficient. High quality goods. The pump works like new.

Review translated automatically

Reliable opinion

2024-05-03, 07:48

View original

Bogusław

Great sealers, they fit nice and tight even though the lag was polished, so far only about 100km after replacement but no drop on the lag, I recommend

Review translated automatically

Reliable opinion

2019-08-26, 12:15

View original

Sławomir

I own a Honda NT650V Deauville. The seals seem solid because of the 2 spring rings. The previous ones only had one such ring.

Review translated automatically

Reliable opinion

2018-03-18, 08:22

View original

Jarosław

Suzuki Intruder 800, seals of good quality, all dimensions met, has been installing for years in various motorcycles, certainly not the last :)

Review translated automatically

Reliable opinion

2024-07-27, 05:08

View original

Bartezz

It fits the Honda CB600F Hornet PC36 perfectly. Charge does not jump, holds the book 13.8 - 14.2 volts depending on the receivers on.

Review translated automatically

Reliable opinion

2023-05-24, 07:13

View original

Remi

Sealers well made, there was no problem with the installation which indicates well-behaved parameters. Tight, oil no longer leaks.

Review translated automatically

Reliable opinion

2020-02-11, 17:50

View original

Piotr

Sealers very good quality not some cheap plastic. There are 2 springs on each sealer. Fast shipping. Recommended.

Review translated automatically

Reliable opinion

2017-04-04, 23:05

View original

Piotr

Honda transalp 600v,1995. Universal kit , well fitted , works flawlessly. Quality of materials at a high level. I recommend .

Review translated automatically

Reliable opinion

2018-05-07, 18:15

View original

Magdalena

WSK M6 B3 1982 Very good quality product easy to install. Fits perfectly, looks very good. Frame worth recommending.

Review translated automatically

Reliable opinion

2023-07-29, 07:17

View original

Sika

Product of good quality as always fast shipping art.I installed in Honda CB 750 Steven fifty degree of difficulty of installation 2/5 I recommend

Review translated automatically

Reliable opinion

2018-01-14, 09:58

View original

Maciej

everything great.consistent with the order,on time and in good quality.this is another purchase from my side that I am satisfied with.

Review translated automatically

Reliable opinion

2025-07-27, 08:46

View original

Eckehard

Good product delivered quickly. I searched for a while to avoid spending so much and found what I was looking for at GMOTO. That's how it should be.

Review translated automatically

Reliable opinion

2020-10-26, 17:04

View original

Mariusz

Honda Shadow 1100 ACE 1996, Front brake repair kit identical to the original, when assembled everything fits perfectly.

Review translated automatically

Reliable opinion

2024-06-22, 08:03

View original

Rafał

The seals fit suzuki gsx600f. Finally stopped leaking from the suspension and its operation improved significantly. I recommend

Review translated automatically

Reliable opinion

2023-08-14, 15:03

View original

Janek

I have not yet assembled and do not know how with the fragility of the plastic, but from the outside it looks positive. On the back a slight unpainting.

Review translated automatically

Reliable opinion

2021-12-21, 10:23

View original

Jacek

Honda CBf 600,2010r.The gaskets fit, whether they will work is what I will know after driving a season, they look quite solid.

Review translated automatically

Reliable opinion

2024-09-11, 14:40

View original

Marcin

Very good quality workmanship fit perfectly to the lags 2 sets mounted on Moto and miles fly nothing leaks.

Review translated automatically

Reliable opinion

2024-11-07, 08:28

View original

Furui

Delivered as ordered. Everything in order. I would order from GMoto again. It is a reliable supplier.

Review translated automatically

Reliable opinion

2021-06-28, 12:41

View original

Tomasz

Kawasaki VN 15 SE from 1991. A set of Athena 41x54x11 front suspension seals - they fit perfectly, like the original.

Review translated automatically

Reliable opinion

2020-05-25, 21:10

View original

Paweł

The frame mounted on the motorcycle and from today it pleases the eye, I did not want to drill the boards and with the product I am satisfied.

Review translated automatically

Reliable opinion